

By the VitraCare Team

"Is the film compatible with my double glazing, with no risk of cracking?" We're asked this regularly before giving an estimate, and it's a fair question: the wrong film can make a pane crack from heat. Here's what happens inside the glass, which situations are risky, what film and glass manufacturers say, and how to choose between fitting the film on the inside or the outside.
Yes, most double glazing can take window film. But not any film on any pane. The risk is called thermal breakage: the glass cracks because it heats up unevenly. With a suitable film on glass in good condition, the risk is low. It rises with dark films that absorb a lot of heat, damaged panes and partial shade.
For reference: to date, we have never had a pane crack after one of our installations. That's our experience, not a guarantee for every window, which is why we look at every glazing unit before we fit anything.
In the sun, the centre of the pane heats up and expands. The edges, held in the frame and shaded, stay cooler. Glass copes badly with this difference: when the tension gets too high, it cracks. According to Contra Vision, a maker of films for glazing, the crack usually starts at the edge, where the glass already had a weak point such as a small chip.
It happens without film too. The Swiss glass maker Glas Trösch mentions radiators, warm air vents and dark furniture placed too close to the glass, and recommends keeping them at least 30 cm away. Film adds one more factor: it absorbs part of the sun's radiation, so the pane it's stuck to gets hotter. The more the film absorbs, the higher the risk.
The type of glass matters a lot. According to the European Window Film Association (EWFA), tempered glass doesn't break from heat in a building, except in a fire, and heat-strengthened glass is very unlikely to. Ordinary glass, called annealed or "float" glass, is the most common. That's the type that can break, and its compatibility should always be checked.
On double glazing, the film goes on the room-side pane. Part of the heat it reflects then goes back into the air gap between the two panes instead of straight outside. An expert from the International Window Film Association (IWFA), quoted by Architect magazine, puts it this way: the outer pane finds it harder to get rid of that heat, and the glass can experience excessive thermal stress.
Manufacturers' compatibility tables point the same way. In the one from Eastman, maker of SunTek films, the same film gets a higher stress score on clear double glazing than on clear single glazing. The manufacturer also mentions a risk specific to double glazing: failure of the seal between the two panes. Contra Vision, for its part, rates low-emissivity ("low-e") double glazing as medium risk.
If your double glazing already has solar control glass, film isn't always useful: our article integrated solar control glazing or film explains the difference.
Eastman's guide adds stress points depending on the pane's situation. Here are the main factors:
| Situation | Why it's a risk | What we do about it |
|---|---|---|
| Dark film that absorbs a lot | The pane gets hotter | Choose a film that reflects rather than absorbs |
| Partial shade on the pane (balcony, tree, neighbouring wall) | One area heats in the sun while the other stays cold. The guide adds 1 to 3 points depending on the shape of the shadow | Check where shadows fall during the day |
| Chipped edges or damaged glass | The crack starts from a weak point. The guide rates chipped edges as "not recommended" | Flag the defect before any installation |
| Very large pane | Stress increases with size. The guide adds 1 point between roughly 4.6 and 9.3 m², and advises against it above that | Check the area of each pane |
| Blind, heavy curtain or dark furniture against the glass | Heat gets trapped against the glass. The guide adds 1 point under 10 cm | Leave some space between the glass and the blind |
| Damaged or missing frame gasket | The glass can't expand as freely | Check the condition of the gaskets |
| Film on only part of the pane | Two areas heat up differently | Always cover the whole pane |
← Swipe to see the full table →
That last point is a rule we always follow for mirror and solar films: our guide to choosing your film explains why we never fit film on just part of a pane.
This is the most telling part of Eastman's table. Each film gets a base score, which is higher the more heat it absorbs. On clear double glazing about 3 mm thick:
| Film (SunTek range) | Score on clear double glazing |
|---|---|
| Clear safety film | 2 |
| Silver mirror film, 20 % light transmission | 6 |
| Matte white film | 7 |
| Neutral tinted film, 20 % light transmission | 11 |
← Swipe to see the full table →
The points for the pane's situation (shade, size, blind...) are added to this score. The manufacturer then allows installation according to the total: up to 10 on any glass, up to 14 only on heat-strengthened or tempered glass, up to 18 only on tempered glass, and above that, not at all.
An example: a T-shaped balcony shadow adds 3 points. The mirror film goes from 6 to 9 and can still go on ordinary glass. The neutral tinted film goes from 11 to 14: it's now only suitable for heat-strengthened or tempered glass. For the same light transmission, a film that reflects heats the glass much less than one that absorbs.
To be honest: these scores apply to SunTek films, not the ones we fit, and we don't have an equivalent table from our supplier. They're useful for understanding the logic, which applies to all films. It's one of the reasons we recommend mirror effect film against heat. Matte white film also stays in a moderate range. And a clear safety film, like the one in our article on security film, barely heats the glass.
They're more cautious than film manufacturers. In its sheet on thermal breakage, the glass maker Glas Trösch writes that insulating glass units must not be painted or covered with film. That's the most cautious position possible, and it makes sense for a glazing manufacturer to take it.
In practice, two simple reflexes. If your windows are recent and still under warranty, reread the terms or ask the manufacturer before fitting. And ask your installer what they base their advice on: Architect magazine, quoting the IWFA, recommends getting the film maker's film-to-glass guidelines in writing, along with the warranties on the film, the glazing and its seals.
Most of the time, we fit the film on the inside. But outside fitting exists and has real advantages in some cases. The films we fit can be applied on either side.
| Inside | Outside | |
|---|---|---|
| Lifespan | The longest, estimated at 10 to 15 years: the film is protected from dirt, cold and rain | Shorter: the film is exposed to the weather and to cleaning |
| Heat | Effective, but on double glazing part of the reflected heat stays in the air gap | The sun is stopped before it enters the double glazing |
| Stress on the glass | The room-side pane heats up | Lower in Eastman's table: 4 instead of 6 for the equivalent silver film on clear double glazing |
| Pets | A dog or cat can scratch the film | The film is out of reach |
| Fitting conditions | Possible in any weather | Needs good weather and safe access to the glass |
← Swipe to see the full table →
Our advice: fit inside in the vast majority of cases, for the lifespan. Outside fitting is worth considering when a pet could damage the film, when the pane gets a lot of sun, or for triple glazing. For a high window, outside access can also make it difficult or even impossible.
To find out what film really changes against heat, whichever side it's on, read our article heat-control window film: does it really work?
On the inside, caution prevails. Contra Vision rates triple glazing as high risk and advises against film fitted on the inside. In Eastman's table, several interior films are rated "not recommended" on it. The UK retailer Streme states that its films, designed for inside use, must not be fitted to triple glazing.
With a film designed for outside use, things are different. Eastman's table for its exterior films gives the silver film a score of 5 on clear triple glazing, within the range allowed for any glass. That's why, on triple glazing, we recommend fitting the film on the outside.
Before every installation, we come and look at the glazing. We check the condition of the windows, the condition of the seals, access to each pane, and the type of glazing: single, double or triple. Above all, we look at your problem, whether it's heat, being overlooked or security. That's what lets us recommend the right film, and the right side to fit it on.
If a pane looks damaged or risky to us, we tell you before fitting. And if you see condensation between the two panes, the double glazing is no longer sealed: film won't change that, as our article replace your windows or add film explains.
The visit is free in Brussels and costs €50 outside. Our article on the steps of a project covers what happens next, and the article on pricing explains how the estimate is calculated.
Eastman Performance Films (SunTek): Film Installation Guidelines, Architectural Window Films (2021)
EWFA, on Glassonweb: Thermal Stress, Film-to-Glass Compatibility (2012)
Glas Trösch: technical sheet 'Bris de verre par choc thermique' (in French)
Contra Vision: Thermal Fracture of Glass, Risks
Architect Magazine: The Effects of Window Films Go Beyond the Surface (April 2012)
Contact us: we'll advise you for free based on your situation and reply within 24 hours.
It can, but it's rare with a suitable film on glass in good condition. The risk rises with dark films that absorb heat, partial shade, very large panes and damaged edges. To date, we have never had a pane crack after one of our installations.
According to Eastman's guide, tempered glass always has a mark in one corner of the pane. If there isn't one, assume the glass is ordinary (annealed), the most common type.
It depends on your window manufacturer. If your windows are still under warranty, reread the terms or ask the manufacturer before fitting. Some glass makers, such as Glas Trösch, advise against any film on insulating glass units as a matter of principle.
Not necessarily. Inside fitting lasts longer and suits most cases. Outside fitting stops the sun before it reaches the double glazing and heats the glass less: it makes sense for triple glazing, a very sunny pane, or if a pet could scratch the film.
Have a window film project?
GET A QUOTE