

By the VitraCare Team

In summer, a south-facing room can become unbearable by early afternoon. Heat-control film promises to fix that without building work, and you'll find it both from installers and in DIY stores. So does it really work, or is it a gimmick? Our answer as installers: yes, but only against part of the heat, and not with just any film. Here's what actually happens in the glass, what the studies say, and how not to be misled by the figures on a spec sheet.
Yes, heat-control film reduces the heat coming in through a sunny window. It sends part of the solar radiation back outside, or absorbs it, before it warms the room. The effect is clearest on a large south- or west-facing window with no exterior blind.
But it only acts on sunlight. It doesn't cool the hot air coming in through an open window, or stop the heat passing through walls and roof. And a figure like '81% infrared rejection' doesn't mean 81% less heat. We explain why below.
The sun sends more than light. According to Saint-Gobain Glass's technical guide, the solar radiation that reaches the ground is made up of about 42% visible light, 55% infrared and 3% ultraviolet. All three carry energy. In other words, infrared isn't the only thing that heats: visible light does too.
When this radiation hits a window, part is reflected, part is absorbed by the glass and the rest passes through. What gets through is absorbed by the floor, furniture and walls. They warm up and give off heat that the glass won't let back out. That's the greenhouse effect, the same one you get in a car parked in the sun with the windows closed.
The right measure of what really gets in is called the solar factor, or g-value (in the US, the solar heat gain coefficient). It's the share of total solar energy that ends up in the room, including the heat the glass absorbed and then released inwards. The lower it is, the less the room heats up.
Heat-control film changes that split: it reflects and absorbs more radiation, and lets less through. Reflective films, such as mirror effect film, send part of the energy back outside. So-called spectrally selective films mainly target infrared and barely affect visible light, which lets them stay clearer.
The US General Services Administration (GSA), which manages federal buildings, had these films evaluated by Lawrence Berkeley National Laboratory. According to its modelling, reflective films are the most effective, with up to 29% savings on heating and cooling energy in warmer climates. But the result depends heavily on the existing glazing: the study finds film cost-effective on single-pane clear glass, and doesn't recommend it on already tinted (bronze) double glazing in most climates. These figures concern office buildings in the United States, in St. Louis and Phoenix. With milder Belgian summers, expect less.
What film doesn't do: it doesn't insulate against hot air. If the room heats up because it's 30 °C outside or because the roof is poorly insulated, film won't change that. Nor does it replace exterior shading, which stops the sun before it even reaches the glass. According to data from the CSTC (the Belgian building research centre) published by Test-Achats, opaque exterior shading lets only 2 to 7% of solar radiation through, against 35 to 59% for opaque interior shading. Film works directly on the glass. Our comparison of solar film and exterior screens helps you choose between the two.
This is where many buyers go wrong. A film spec sheet gives several percentages that don't measure the same thing:
| Figure | What it measures | What it doesn't tell you |
|---|---|---|
| Visible light transmission (VLT) | The share of daylight that gets through: the lower it is, the darker the room | Heat |
| UV rejection | The share of ultraviolet blocked, the main cause of fading | Heat: UV is only about 3% of solar energy |
| Infrared rejection (IRR or IRER) | The share of infrared blocked | Total heat, since visible light heats too |
| Total solar energy rejected (TSER) or g-value | The share of all solar energy that doesn't get in (TSER = 100% minus g) | The result on your glazing, if it was measured on different glass |
← Swipe to see the full table →
A real example: on the spec sheet of a reflective film from Solar Gard (part of the Saint-Gobain group), the same film rejects 73% of infrared but 67% of total solar energy on single clear glass. And the sheet gives different values for single, double and triple glazing. So, two good habits: compare total solar energy rejected rather than infrared, and check which glass the measurement was made on.
The mirror effect film we install has a visible light transmission of 22%, rejects 72% of UV and 81% of infrared. That 81% doesn't mean 81% less heat, for the reason explained above, and the real gain also depends on your glazing. Our article on UV protection explains what the UV figure measures.
If heat is your main problem and you also want to cut down on being overlooked, mirror effect film is the most effective of the films we install. It's a reflective film, the family that performs best in the study above. In return, the room is darker, a bit like wearing sunglasses.
If you want to keep a bright room and a perfectly clear view, solar film filters heat more moderately, with a slight blue tint. Our guide to choosing your film puts all the options side by side.
A darker film isn't necessarily better against heat. What counts is total solar energy rejected, not the colour. Keep that in mind with films sold in shops: our comparison of cheap film and professional installation explains what to check.
Film gives the best results where the sun hits the glass directly for hours. Elsewhere, the effect is smaller, or nil:
| Situation | Does film help? |
|---|---|
| Large south- or west-facing window, no exterior blind | Yes, it's the most favourable case |
| Conservatory or very glazed room | Yes, often alongside exterior shading |
| North-facing window, or in shade all day | Little: there's not much direct sun to filter |
| Heat coming mainly through the roof or walls | No: film only works on windows |
| Roof window (Velux type) | Exterior shading is a better fit |
← Swipe to see the full table →
For roof windows, our article on Velux windows that get too hot explains why we recommend exterior shading instead. If you're weighing film against air conditioning, our film or air conditioning article compares the two. And if your windows are single-glazed and in poor condition, the article replace your windows or add film helps you decide.
We apply these films directly to your existing windows, generally on the interior side, in a single visit and with no removal. The installation is guaranteed for 2 years, and the film's lifespan is estimated at 10 to 15 years for an interior installation. Our article on the steps of a project walks through the process, from measurements to installation.
There's no published price list: the price depends on the surface area, and stays the same whichever film you choose. Our article on pricing explains how the estimate is calculated.
Contact us: we'll advise you for free based on your situation and reply within 24 hours.
Yes, it's applied on the interior side of single and double glazing alike. The gain does depend on the existing glazing, though: Lawrence Berkeley National Laboratory's evaluation for the GSA shows clearly better results on single clear glass than on already tinted double glazing.
It depends on the film. Mirror effect film lets 22% of visible light through: the room is noticeably darker, a bit like wearing sunglasses. Solar film stays transparent, with a slight blue tint.
It isn't insulation. It filters the sun whenever it hits the glass, winter included, but we don't promise any heating savings, as there's no reliable measurement for this product.
Not necessarily. First check that the packaging gives total solar energy rejected, not just infrared or UV: without that figure, you can't compare. Wet application on a large pane also takes practice to avoid bubbles and creases.
Have a window film project?
GET A QUOTE